Aire One Peel Heating & Cooling · Mississauga and Peel Region · Updated November 2026
Radiator Maintenance: Bleeding, Pressure and Balancing, and When to Call
By Mario Vaghei, General Manager, Aire One Peel Heating & Cooling · Published November 16, 2026 · Facts verified November 12, 2026
Short answer
Hot water radiators need three simple things from the homeowner: bleed out trapped air when a radiator is cold at the top, keep the boiler pressure in the range its manual gives, and keep the radiators clean and unobstructed. Natural Resources Canada says hydronic systems "perform best when radiators are relatively free of air bubbles and operating at correct pressures." Uneven heat from room to room is usually a balancing issue, and annual maintenance of the boiler itself belongs to a qualified service technician.

On this page
Signs a radiator needs attention · How to bleed a radiator · Pressure: read the gauge against your boiler's manual · Balancing: when some rooms are cold · Keep radiators clean and unobstructed · What belongs to a technician · When to call · Frequently asked questions
Signs a radiator needs attention
- Cold at the top, warm at the bottom: air is trapped and needs bleeding.
- Gurgling or knocking: often air in the system.
- Some rooms hot, others cool: the system may need balancing.
- The boiler pressure gauge reads low after bleeding: the system lost water and may need topping up.
- Dust on baseboard fins, or bent fins: less heat reaches the room.
How to bleed a radiator
NRCan recommends bleeding radiators on a regular schedule unless your system bleeds automatically. The usual steps:
- Turn the heating off and let the radiators cool. Hot water under pressure can scald.
- Find the bleed valve, a small valve at one top corner of the radiator, and hold a cloth under it.
- Open it slowly with a radiator key or a flat screwdriver. You will hear air hiss out.
- Close it as soon as water appears in a steady stream.
- Repeat on the other radiators, then turn the heating back on.
- Check the boiler pressure gauge. Bleeding lets out a little water, so the pressure drops. Compare it with the range in your boiler's manual.
If the pressure is below the manual's range and you are not sure how to refill the system safely, call a technician rather than guessing. If a radiator needs bleeding every few weeks, air or water is getting in or out somewhere, and that is a service call.
Pressure: read the gauge against your boiler's manual
A hot water system is designed to run at a set pressure, and Natural Resources Canada names "correct pressures" as one of the two things hydronic systems need. The right number depends on your boiler and your house, so the range printed in the boiler's manual is the one to use. A gauge that keeps falling or climbing is a fault to report, not a setting to keep adjusting.
Balancing: when some rooms are cold
If bleeding does not even out the heat, the system may need balancing. NRCan says adjusting the valves on a hot water system can help even out heat distribution, and if that does not work, to hire "a competent contractor to upgrade or balance your system." Balancing means setting how much hot water each radiator or loop receives, so the rooms nearest the boiler stop taking all of it.
Keep radiators clean and unobstructed
- "Vacuum the radiators of electric or hydronic baseboard systems each autumn to prevent dust buildup." (NRCan)
- If baseboard fins are bent, "gently straighten them with a plastic comb to improve their efficiency." (NRCan)
- Keep furniture and long curtains off radiators so the heat reaches the room.
- On exterior walls, NRCan suggests placing foil-covered insulation board between the radiator and the wall "to reflect heat back into the room."
What belongs to a technician
Natural Resources Canada says "a qualified service technician should perform annual maintenance and efficiency tune-ups", even though homeowners can handle some tasks. For a gas or oil boiler that yearly visit also covers the safety checks; our boiler service checklist lists what it includes and the TSSA carbon monoxide check that applies to some boilers in Ontario. NRCan also mentions an outdoor reset control, which adjusts the circulating water temperature to the weather and can lower energy use; ask about it at the yearly visit.
If you are choosing a heating system rather than maintaining one, our comparison of furnaces, heat pumps, dual fuel and boilers covers when a boiler makes sense.
When to call
Call a technician if the boiler pressure keeps dropping, a radiator leaks, the boiler shows an error, or bleeding and balancing do not fix cold rooms. For heating advice, call Aire One Peel at 905-564-8545.
Frequently asked questions
How often should radiators be bled?
Natural Resources Canada recommends bleeding radiators on a regular schedule unless the system bleeds automatically, and any time a radiator is cold at the top and warm at the bottom.
Should the heating be on or off when bleeding radiators?
Off, with the radiators cooled down. The water inside is hot and under pressure.
Why does my boiler pressure drop after bleeding radiators?
Bleeding releases a little water along with the air. Check the gauge against the range in your boiler's manual afterwards; if it keeps dropping, call a technician.
Why are some radiators hot and others cold?
Trapped air is the first thing to rule out. If bleeding does not fix it, the system may need balancing; NRCan suggests adjusting the valves and, if that fails, hiring a competent contractor to balance the system.
How do I clean baseboard radiators?
Vacuum them each autumn, as Natural Resources Canada recommends, and gently straighten bent fins with a plastic comb.
Sources and references
- Canada.ca, "Keeping the Heat In", Section 9 (operating your house: heating systems), read November 12, 2026.



