Aire One Peel Heating & Cooling · Mississauga and Peel Region · Updated November 2026
How a Heat Pump Installation Works in Ontario: Steps and What to Prepare
By Mario Vaghei, General Manager, Aire One Peel Heating & Cooling · Published November 16, 2026 · Facts verified November 12, 2026
Short answer
A heat pump installation in Ontario starts long before installation day. The house is measured for heat loss and the ductwork is checked, you collect written estimates from TSSA-registered contractors, and if you want the Home Renovation Savings rebate the pre-approval has to be in place before any equipment goes in. On installation day the outdoor unit, the indoor coil or heads, the refrigerant lines and the wiring go in, and the system is started and checked. Afterwards the contractor files the rebate paperwork, and the heat pump gets an inspection every year.

On this page
Step 1: Measure the house, not the old unit · Step 2: Get written estimates from registered contractors · Step 3: Decide on backup heat · Step 4: Get the rebate pre-approval before installation · Step 5: Installation day · Step 6: Start-up and a walk-through · Step 7: The rebate paperwork · Step 8: A yearly inspection · When to call us · Frequently asked questions
Step 1: Measure the house, not the old unit
Save on Energy's heat pump buying guide puts this first: "Assess the size, construction and layout of your home to calculate heat loss." The contractor should also check whether your existing ductwork can carry the airflow the new equipment needs. In an older home, the same guide suggests doing efficiency work first "to reduce your heating load", which can make a smaller and less expensive heat pump enough.
Canada.ca is blunt about why this matters: "Improper sizing or installation of a heat pump can result in financial consequences and reduced efficiency." It suggests asking the contractor directly: "How are you ensuring that the heat pump is properly sized for my home?"
Step 2: Get written estimates from registered contractors
Save on Energy recommends written estimates from at least three contractors and notes that "In Ontario, HVAC contractors must be registered with the Technical Standards and Safety Authority." Compare what each estimate includes, not only the total. Our heat pump price guide shows the 2026 installed ranges by system type, so you can tell whether a number is in the normal band.
Step 3: Decide on backup heat
A heat pump can be the only heat source, or it can work beside a furnace. Save on Energy describes the hybrid set-up as "a conventional furnace or boiler acting as a backup to a primary air source heat pump", and says the choice depends on climate, energy costs, heat loss and the type of home. If you heat with gas today, our pros and cons of switching from a furnace to a heat pump walks through that decision.
Step 4: Get the rebate pre-approval before installation
For the Home Renovation Savings Program, the order matters. The program's heat pump page says "Pre-approval is mandatory. Installations done before approval are not eligible for rebates." The model must be on Natural Resources Canada's qualified products list for cold-climate air-source or ground-source heat pumps, the work is done by a participating contractor, and the contractor submits both the pre-installation and the post-installation applications. A home energy assessment is not required for this rebate. The amounts, by your current heating fuel, are in our Ontario rebates guide.
Step 5: Installation day
What goes in depends on the system type:
| Part | Ducted heat pump | Ductless mini-split |
|---|---|---|
| Outdoor unit | One unit, placed with clearance for airflow and service access | One unit, serving one or more indoor heads |
| Indoor side | A coil on the furnace or a new air handler, on your existing ducts | Wall or ceiling heads in each zone |
| Refrigerant lines | Run between the outdoor unit and the indoor coil | Run to each indoor head |
| Electrical | A dedicated circuit; Save on Energy notes installation "may involve modifying ductwork and wiring" | A dedicated circuit; wiring to each head |
| Controls | A central thermostat | Each head's control, or a central control |
Table: Save on Energy heat pump buying guide and Canada.ca heat pump basics, read November 12, 2026. The refrigerant work is regulated: Ontario requires an Ozone Depletion Prevention certificate card to handle refrigerants, and a Certificate of Qualification in a trade such as refrigeration and air conditioning mechanic to work on the equipment.
Step 6: Start-up and a walk-through
Before the installer leaves, the system should be started in heating and cooling and you should be shown how the controls work, how backup heat comes on if you have it, and where the filter is. Ask for the model numbers and the installation date in writing: you need them for the warranty registration and the rebate. Our heat pump warranty guide explains why registration timing matters.
Step 7: The rebate paperwork
After installation, the participating contractor submits the post-installation application for the Home Renovation Savings rebate. Keep the invoice and the model and serial numbers with your records.
Step 8: A yearly inspection
Save on Energy's advice for after installation is short: "make sure you get it inspected annually." Our heat pump maintenance guide covers what that yearly visit includes. For how a cold-climate unit behaves in a Peel winter, see our guide to heat pumps in cold weather.
When to call us
For a heat loss calculation and a written estimate, start with heat pump installation in Mississauga or call 905-564-8545.
Frequently asked questions
What are the steps of a heat pump installation in Ontario?
Heat loss calculation and ductwork check, written estimates from TSSA-registered contractors, the choice of backup heat, rebate pre-approval, installation of the outdoor unit, indoor coil or heads, refrigerant lines and wiring, start-up and a walk-through, the post-installation rebate application, and a yearly inspection.
Do I need rebate approval before installing a heat pump?
Yes, for the Home Renovation Savings Program. Its heat pump page says pre-approval is mandatory and installations done before approval are not eligible for rebates.
Who is allowed to install a heat pump in Ontario?
Save on Energy notes that HVAC contractors in Ontario must be registered with the Technical Standards and Safety Authority. Refrigerant work also needs an Ozone Depletion Prevention certificate card and a Certificate of Qualification in a trade such as refrigeration and air conditioning mechanic.
How is a heat pump sized?
From a heat loss calculation of the house: its size, construction and layout. Canada.ca warns that improper sizing can lead to financial consequences and reduced efficiency.
Does a heat pump need maintenance after installation?
Yes. Save on Energy advises having it inspected annually.
Sources and references
- Save on Energy, "Heat Pump Buying Guide", read November 12, 2026.
- Home Renovation Savings Program, heat pump rebates, read November 12, 2026.
- Canada.ca, "Heat pump basics", read November 12, 2026.
- Government of Ontario, "Certificate to handle refrigerants", read November 12, 2026.



